我每次要調音的時候常常遇到一個問題.就是每當我調好音(換完弦OR調降半音)之後.鎖上琴頸(鎖空弦那排)上的那三粒內六角螺絲之後再看琴的音準結果都跑掉了~__~ 我的琴型號是STRATOCASTER~邦喬飛吉他手簽名紀念琴~ 希望能請教有關這類琴的調音方法~ 先肛溫了!!
HI, this is normal when changing strings if you are not too familiar with Floyd Rose type floating bridge & traditional Fender floating bridge. It was mainly due to the tension of the 1/2/3 strings not balance with the 4/5/6 string, or may be your floyd rose was not set up properly. Now, first, unlock your locking nuts, i.e., loosen the three hex screws. After doing this, you will be able to tune the guitar with your machine heads. As you have unlocked your locking nut, tune your guitar from your first string to the sixth string again. After you have tuned the sixth string to low E, then check the first three strings by your tuner. You will notice that those first three strings will become flat and out of tune. Then, tighten the first three strings a bit, but not too much, and don't tune them to normal pitch now. After this, if you check the pitch of the low E string, it was flat and out of tune agin. At this moment, tune the 4/5/6 strings to pitch. After your 4/5/6 strings in correct pitches, then back to tune the 1/2/3 strings. You will find the first three strings just a little bit more sharp. So, patiently check & tune all those six-string to normal pitch. When all your six strings was in tune, look at the base plate of the floyd rose, if the base plate was parallel to the guitar body. Then, lock your locking nuts, and use the fine tuners on the floyd rose bridge to tune. In case, the base plate of the floyd rose was not parallel to the body of the guitar, your floyd rose need to set-up again. Contact your guitar repair tech in local music store or ask your friend who was experienced in floyd rose bridge to help you out. Sorry to write in English, since the PC in my office was with English Windows. IF you need explanation in Chinese, please e-mail to me. Good luck Best regards, Patrick
HI, Y鳥, 對不起. 因我office只有英文Windows, 所以用了英文寫. 現, 我剛回到家,隨後, 我會用家中有中文Windows的pc以e-mail回覆你. Best regards, Patrick
Hi, Y鳥兄, 關於閣下結他上Floyd Rose Bridge的問題, 是一般floating bridge (Floyd Rose, traditional Fender floating bridge)常見, 主要因換了其他牌子同粗度之結他絃(e.g 本來用Fender009/042絃而改用GHS 009/042), 或換上不同gauge的結他絃(e.g 本來用009/042絃而改用010/046). 言歸正傳, 以下為解決方法 : 1) 相信你的結他之locking nut己lock了, 首先請你把locking nut上三條六角縲絲鬆開, 現你可以用Machine heads tune結他. 同時也請你把Floyd Rose上的Fine tuners調到中位. 2) 請由第一絃開始tune結他, 當你把第六絃tune到low E時, 再用結他tuner check第一/二/三絃時, 這三條絃已走了音. 主要因為第4/5/6絃的tension 拉力比 1/2/3絃高, 所以, 你把4/5/6絃tune好了後, floating bridge 升起了一點, 1/2/3絃便flat 了. 3) 現, 請你把1/2/3絃調高一點, 但, 暫不需check是否in tune. Floating bridge 因1/2/3絃調高而升起了一點, 所以你需主力把4/5/6絃tune to pitch. 4) 當你把4/5/6絃tune好後, 你再用結他tuner check 1/2/3絃時, 你會發覺1/2/3絃只sharp了一點. 之後, 請再細心再tune 一 tune 六條絃. 這次, 相信很容易把六條絃全tune至in tune. 5) 當六條絃全in tune, 請看一看floyd rose floating bridge的base plate是否和琴面平衡. 如base plate和琴面平衡, 現可把locking nut lock上. 因locking nut lock上時為六條絃帶來pressure, 所以lock上後, 六條絃因pressure帶來的extra tension 而sharp了. 此時, 你可用floyd rose上的Fine tuners 再tune to pitch. 這便完成了整個tuning步驟. 6) 但, 如果當六條絃全in tune, floyd rose floating bridge的base plate不是和琴面平衡, 你的結他便需set-up, 最好請教貴方結他店的師傅這方面的做法或請他把你的結他set-up. 希望能給閣下一點idea. Best regards, PATRICK