POD XT外接EQ

本文由 大拳王2004-10-20 發表於 "效果器、Amp、DIY" 討論區

  1. 大拳王

    大拳王 New Member

    註冊日期:
    2003-09-10
    文章:
    76
    讚:
    0
    想請問..是不是有可能在XT 加裝個EQ又使用到他的音箱模擬上的破音,像下面
    POD模擬音箱上破音->外接的EQ->原本的POD空間系效果器

    如果有的話可否請教如何裝呢
     
  2. 雜唸Roger

    雜唸Roger Member

    註冊日期:
    2002-04-05
    文章:
    450
    讚:
    19
    因為XT的Effects Routing都是固定的,只能設定Pre或者Post(音箱之前或之後)但沒辦法更改你要的前後順序,另外XT V2.0之後就有Post EQ應該不需要外接EQ
     
  3. 大拳王

    大拳王 New Member

    註冊日期:
    2003-09-10
    文章:
    76
    讚:
    0
    似乎只有 XT PRO可以做FX LOOP
    新版的POST 4BAND EQ 其實雜音很大而且並沒有想像的好用....
     
  4. 大拳王

    大拳王 New Member

    註冊日期:
    2003-09-10
    文章:
    76
    讚:
    0
    忘記謝謝雜念ROGER的回答呢...果然是當代萬事通
    感恩感恩
     
  5. 雜唸Roger

    雜唸Roger Member

    註冊日期:
    2002-04-05
    文章:
    450
    讚:
    19
    XT Pro有Loop但因為XT Pro的Loop是擺在所有效果的最後面還是沒辦法做到你想要的那樣,其Effects Routing還是固定的......
    其實XT Pro的4 Band EQ設計的不甚理想因為Bandwidth是固定的不能調但已經算堪用,我到不覺得Post EQ有雜音的問題,就算有雜音應該也不是來自於Post EQ這部份如果你有擴充Amp Pack,裡面72組音箱的音色幾乎已經足夠應付需要的音色....
     
  6. wenyushn-小溫

    wenyushn-小溫 New Member

    註冊日期:
    2001-12-31
    文章:
    243
    讚:
    0
    BAND有四段,頻帶都有可以調整的範圍
    應該沒有雜音,除非琴或機器受到干擾
     
  7. 雜唸Roger

    雜唸Roger Member

    註冊日期:
    2002-04-05
    文章:
    450
    讚:
    19
    frequencies可以調但是頻寬Q Bandwidth是固定的沒辦法調整,想必Line6還是要讓Vetta跟XT有所差別,因為4-Band EQ是從Vetta移植過來的,Vetta有Q可以調但XT卻沒有..........

    另外XT還有XT Pro的v2.1的韌體也快出了.....
    下面是更新內容,大致上跟XT Live目前的V2.1沒兩樣...
    *A new update for PODxt/Pro - version 2.1 - is currently being tested and currently scheduled for release in November 2004.
    *Much like we made all new studio cabs for v2.0, we made all new live cabs for PODxt Live. We also replaced the not-so-popular preset driven "VIBE" EQ parameter with new user-controllable "Tonestack Correction" parameters. In FAQ Trak, we have posted recommended correction settings for many popular amps. PODxt/Pro v2.1 has all of the new live cabs, the "bypass amp" feature, and the Tonestack Correction that was created for PODxt Live.
    *If you use an FBV Shortboard with a PODxt Pro, you can now assign the FX Loop switch to control Comp instead of the FX Loop (like the Bean always does). The bean users have thought this was cool because that way you can set up your Comp switch as a "boost" by using the compressor gain.
    *We have said in the past that for PODxt Pro, the processing power used to create a different signal at the XLR outs from the 1/4" outs was used on the bean to do VIBE mode. This is why PODxt Pro doesn't have VIBE modes. For this update, we decided to give users the choice - the Tonestack Correction parameters ARE on the Pro, but when you use them, you get the same signal at the XLR and 1/4" outs. A little kludgey I know, but at least now there isn't anything on the Bean that you can't do with the Pro and that's the right thing to do...
     
  8. solid

    solid New Member

    註冊日期:
    2004-01-09
    文章:
    111
    讚:
    0
    說到裡面的EQ...真是一點也看不太懂@@"
    那位熱心的前輩可以給小弟一點指引呢^^"
     
  9. wenyushn-小溫

    wenyushn-小溫 New Member

    註冊日期:
    2001-12-31
    文章:
    243
    讚:
    0
    感謝ROGER兄的指正

    FREQ是調整的位置點

    Q值是指調整FREQ該點的影響範圍(CRYBABE 535 Q就是這樣設計的)
    GAIN是該FREQ點的放大率

    那台pro如果明年4月還沒賣出,我就透過usb加上analog device的開發軟體看看能不能把一些vetta的東西放進去
     

分享此頁面