將Cilck回錄: 1.假設你的Monitor是接在 audio interface 的 output1-2 2.打開 VST Connections window,選Outputs tab 3.Add 2個 stereo Bus,假定是 "Stereo Out 1" 和 "Stereo Out 2" 4.Set "Stereo Out 1" as Main Mix ,Device Port 設在 output3-4 5."Stereo Out 2" 的 Device Port 設在 output1-2 6.選VST Connections window 的 Inputs tab 7.Add 1個 mono Bus, Device Port 設在 input1 8.用一條導線,從 audio interface 的 output3 接到 input1 9.回到Project window,新增1個mono track,取名為 "Click" 10.將"Click" track 的 input 設在input1; output 設在"Stereo Out 2" 11.將 Nuendo 的click 打開,按下錄音鍵,就可以回錄了! 要注意Latency 的問題,所以建議將 Buffer size 調小... 錄完可以放大波形檢查,看回錄的click有沒有對齊小節線,必要時可手動調整位置...
感謝c大 我照你說的方式了 不過還是沒成功 可能我某個環節出錯了 我是用M-audio first track當錄音卡 另外我也參考了youtube的教學影片還是沒成功.... http://www.youtube.com/watch?v=zZ-s7tDDrLc
有求知的慾望也有錯嗎? 放個鼓點LOOP進去誰不會啊? 不過我就是想知道怎麼內錄 可是就一直找不到方法 所以才會來這裡請益前輩們 對你來說這是垃圾文章 但對我來說很重要 每個人的觀點不同 如果你知道答案不告訴我還好 不要不知道還來酸我 謝謝(抱歉 我被搞瘋了)
不客氣... 我今天又試了一次,發現在VST Connections->Outputs tab, Set "Stereo Out 1" as Main Mix, 竟然聽不到click ... 昨天明明還可以聽得到...%#$&#$%^#%^ 沒關係,可以設在 Studio tab... 所以,又因為你的是FastTrack ,只有2個output, 可以試一下這個方法: 1.將你左邊的Monitor接在 FastTrack 的 output1,右邊的Monitor先不接 2.打開 VST Connections window,選Studio tab 3.按"Add Channel", 選 "Add Monitor", Name "Monitor 1", Configuration 選 Mono, Device Port 設在 FastTrack 的 output2 4.選 VST Connections 的Outputs tab,Add 2個 mono Bus,假定是 "Mono Out 1" 和 "Mono Out 2", Set "Mono Out 1" as Main Mix ,Device Port 設在 "Not Connected"; "Mono Out 2" 的 Device Port 設在 FastTrack 的output1 5.選VST Connections 的 Inputs tab,Add 1個 mono Bus, Device Port 設在 FastTrack 的 Guitar Input 6.用一條導線,從 FastTrack 的 output2 接到FastTrack 的 Guitar Input 7.回到Project window,新增1個mono track,取名為 "Click" 8.將"Click" track 的 input 設在FastTrack 的Guitar Input; output 設在"Mono Out 2" 9.將 Nuendo 的click 打開,按下錄音鍵,就可以回錄了! 我自己試過是ok的... 另外,你提到的 youtube link,他下面有說到"if the sound card (or the audio interface) allows internal routing." 還有 "Some consumer level audio cards and semi-professinal audio interfaces do not allow the signal to be routed internally like this. If this is the case, you'll have to either: 1- connect one of your physical outputs to your physical inputs via cable or, 2- output the click/metronome sound as MIDI and use a VSTi instead." 也就是說,FastTrack 應該沒辦法internal routing, 必需connect one of your physical outputs to your physical inputs via cable