請問Fret可以只Refret一格的嗎??

Discussion in '吉他' started by amj80052809, Feb 11, 2012.

  1. amj80052809

    amj80052809 New Member

    Joined:
    Apr 8, 2010
    Messages:
    281
    Likes Received:
    0
    小弟剛入手一把Dean，它的第四格比其他格低一點，需要調整才能重新上陣
    因為如果用磨的，恐怕第四格後的Fret都要磨
    不如把第四格Fret換掉或是重新安裝成適當的高度
    有認識大大可以這樣做的嗎???價格大約是多少???
    (真希望可以500以下搞定...最近同時壞了多把琴...)
     
    amj80052809, Feb 11, 2012
    #1
  2. rockheart

    rockheart Member

    Joined:
    May 4, 2009
    Messages:
    445
    Likes Received:
    4
    我記得可以

    不過絕對不是500元搞定的(金螞蟻說不定可以XD

    還要看你的指板是什麼
     
    rockheart, Feb 11, 2012
    #2
  3. amj80052809

    amj80052809 New Member

    Joined:
    Apr 8, 2010
    Messages:
    281
    Likes Received:
    0
    QQ最近超多把琴要維修的啦！應該說手邊沒有一把琴是好的．．．
    大多都是線路問題　不過這把狀況比較特別

    Refret一格要超過五百塊喔！！？？
     
    amj80052809, Feb 11, 2012
    #3
  4. amj80052809

    amj80052809 New Member

    Joined:
    Apr 8, 2010
    Messages:
    281
    Likes Received:
    0
    我的是玫瑰木　整把琴狀況很好　有沒有知道什麼可以解決打弦的方法嗎？
     
    amj80052809, Feb 11, 2012
    #4
  5. amj80052809

    amj80052809 New Member

    Joined:
    Apr 8, 2010
    Messages:
    281
    Likes Received:
    0
    所以貴的主要是工錢吧？？？
     
    amj80052809, Feb 11, 2012
    #5
  6. a22040467

    a22040467 Member

    Joined:
    Dec 29, 2009
    Messages:
    202
    Likes Received:
    0
    先拿去給樂器行看看吧,搞不好不用REFRET就可以解救的問題,如果要單一格RE算起來不會比整把去RE還划算唷
     
    a22040467, Feb 11, 2012
    #6
  7. taiwanluthiers

    taiwanluthiers New Member

    Joined:
    Aug 9, 2007
    Messages:
    235
    Likes Received:
    0
    Fret 工程是很費工。一個 fret 平均需要約 10 分鐘的工時，而且換一條 fret 全部一定要磨平，磨平之後 fret 還要復為圓形，然後拋光。
     
    taiwanluthiers, Feb 11, 2012
    #7
  8. hjack

    hjack Member

    Joined:
    Aug 19, 2010
    Messages:
    542
    Likes Received:
    0
    只換一條五百可以搞定，(其實一般的材料不到50元，有勇氣可以自己換..)
    問題在"修整"一條的"結果"
    不一定比現在更好

    貴在整支打磨、修邊的工錢跟技術


    還有個濫招，把Fret摳起來一點點，讓他變高
     
    hjack, Feb 11, 2012
    #8
  9. douglennon

    douglennon Active Member

    Joined:
    Aug 26, 2005
    Messages:
    645
    Likes Received:
    98
    不換fret，要磨第四格之後

    換一根fret，要磨全部，還要保證新的那根跟舊的是同一size



    如果是我當然去作redress

    尤其如果neck還有binding的話
     
    douglennon, Feb 11, 2012
    #9
  10. amj80052809

    amj80052809 New Member

    Joined:
    Apr 8, 2010
    Messages:
    281
    Likes Received:
    0
    好的 感謝各位大大的回覆 小弟瞭了!!!
     
    amj80052809, Feb 15, 2012
    #10

Share This Page